Adirondack Chairs. Before You Buy

Adirondack Chairs. Before You Buy

How can you tell if you are getting value for your money?

Not all Adirondack chairs are created equally but its very difficult to tell quality when all you have to base your opinion on is a photo. So here are some of the things you should consider when purchasing an Adirondack chair.


When comparing Adirondack chairs here are a few things to look for.

Leaning back. Adirondack chairs were originally designed to sit on a hill or mountain when placed on ths sloped surface the chair actually sat level. Most took this chair and put it on fla surfaces without adjusting the recline of the chair. thus the standard chair leans back too far and makes it hard to get in and out of. Make sure the back has a gentle lean. not a lounge chair lean.

Flat backs vs Curved backs. flat backs are hard on your spine when sitting but curved fan style backs that are too dastically curved cause you to hunch your shoulders forward in order to lean back i the chair causing stress between the shoulder blades. The curve should be slight as the natural curve between your shoulder blades.

Seat curve. If you see a dramatic curve in the seat odds are its not going to be as comfortabl as a gentle curve. A dramatic curve creates steep edged angles of the slats scre ed on top which dig in when you are sitting. Better a flat seat than one that is overly curved but the slight gentle curve is the most accommodating so long as the seat does not curve in too much. Too much of a curve can also cause pressure points behind the knees.

Seat bottom. Some chairs have a wide last seat slat custom shaped to fill the gap where the back cuves around the seat... that gap is actually more comfortable left unfilled than havin a flat piece of wood that often digs into the tail bone because it angles upwards following the curve of the chair seat. It may look prettier but it is less comfortable and can potentially cause problems for the lower spine.

Seat front. The front of the Adirondack Chair seat may be cut flat behind your knees. If so keep inmind that this edge can dig in under your knees creating pressure points that will cause your feet to fall asleep.

Legs under the seat. The legs under the seat should have a solid brace system either cross braces or more prefrably a large board that is screwed in multiple places in order to create a soli foundation.

Back bracing. The Back should be very well braced especially where the back meets the seat as that is te weak point in most Adirondack chairs. This is even more essential in Adiron ack chairs that fold. Three back braces are stronger than two and help eliminate wiggling of the chair.

Those are just a few of the things that add to the comfort. of course there will be esthetic differences in designs that one will prefer over another.

Wood. Not all woods hold up well in all climates but if you are looking for something cheep that you will be replacing in a year or so just about any material will suffice. If however you are looking for a long term investment into a better Adirondack chair quality then you need to consider the following.

Pine. Is fine for short term but is not termite resistant and is prone to water damage, mildew and rotting. To make pine last longer be sure to put a good finish on it including a primer and high UV rating top coat. Pine can last longer than a few years but it requires regular maintenance. This is a cheep wood available anywhere and is most often used in third world made products Malaysia, China, etc.. Watch out for pressure treated pine as the chemicals used in pressure treating can be harmful to your health.

Cedar. This is the best softwood for longevity as it is naturally impervious to rot and the cedar oils deter insects. Cedar is the choice wood for decks, boardwalks, and such due to its high durability and easy availability in North America as it is a native wood to our country. Marks and blemishes can be easily sanded away and cedar can last many generations. If left unfinished it will eventually turn to a soft silvery grey and in a decade small fissures will show up in the wood surface but they do not compromise the strength or life of the wood. There are many species of cedar but the longest lasting of them is western red cedar.

Teak. This is a very heavy hardwood that can last incredibly long generations. Its density creates the heavy weight to this wood and like cedar it is naturally impervious to termites. Teak is imported and not a native wood to North America and with its heavy weight and high demand it is incredibly expensive up to 3 times the price of products made in cedar, up to 6 times the price of products made of pine. Teak is difficult to care for as it does not take a stain well.

NOTE. A few manufacturers are now conscious of global concerns surrounding destruction of rainforests and wildlife thus use only Certified Sustainably Harvested.

Blog Post

Featured post

How To Choose The Right Big And High Office Chair

Continue reading
Blog Post

Featured post

Ghost Chairs Invisible Entrance to the Furniture World

Continue reading

Home | Privacy Policy | Contact Us

© Copyright 2019